How to insulate a climate-controlled wine cellar
We design the thermal insulation of a wine cellar for the specific building, the adjacent spaces and the operating conditions. The design includes an assessment of heat gains and suitable construction build-ups. Suitable insulants are those that do not absorb moisture – EPS, XPS or PUR, not mineral wool. For a 25 m³ cellar, the manufacturer of Wine Master cooling units specifies at least 110 mm EPS, 80 mm XPS or 60 mm PUR.
01
Why insulation matters more than the cooling unit
Insulation determines how much heat enters the cellar; the cooling unit merely removes it. Cooling unit manufacturers therefore always state the maximum cellar volume on condition of insulation according to their table, and in the manuals for its cellar units Wine Master also makes the warranty conditional on it. Good insulation also reduces energy consumption and helps keep humidity stable.
02
Minimum insulation thickness by volume
The manufacturer’s tables apply to an internal temperature of 12 °C and are given for all surfaces of the cellar. Each cooling unit model has its own table in its manual – two examples are shown below.
Wine IN25 X (cellars up to 25 m³)
| Cellar volume | EPS (λ 0.044) | XPS (λ 0.030) | PUR (λ 0.025) |
|---|---|---|---|
| 6 m³ | 40 mm | 30 mm | 30 mm |
| 10 m³ | 60 mm | 40 mm | 40 mm |
| 16 m³ | 80 mm | 60 mm | 50 mm |
| 20 m³ | 90 mm | 70 mm | 60 mm |
| 25 m³ | 110 mm | 80 mm | 60 mm |
Wine SP40 CA PRO (cellars up to 40 m³)
| Cellar volume | EPS (λ 0.044) | XPS (λ 0.030) | PUR (λ 0.025) |
|---|---|---|---|
| 8 m³ | 30 mm | 20 mm | 20 mm |
| 16 m³ | 60 mm | 40 mm | 40 mm |
| 24 m³ | 90 mm | 60 mm | 50 mm |
| 32 m³ | 120 mm | 80 mm | 70 mm |
| 40 m³ | 150 mm | 100 mm | 90 mm |
λ is the thermal conductivity in W/m·K – the lower it is, the better the material insulates and the thinner the layer required.
03
Which insulant to choose
- EPS (expanded polystyrene) – the most affordable, but needs the greatest thickness; perimeter-grade EPS is used in contact with soil. It is what we use most often in practice, or alternatively XPS.
- XPS (extruded polystyrene) – better insulating performance and minimal water absorption; also suitable in contact with soil or under the floor, if the floor is insulated.
- PUR/PIR (polyurethane) – the thinnest layer for the same effect; not attacked by rodents.
- Unsuitable: mineral wool (glass or stone) – absorbs moisture and loses its insulating capacity; thin reflective foils – ineffective against cold.
Join the boards with tongue and groove or bond them together so the insulation is continuous. Protect them with cladding – faced composite boards or sandwich panels – against damage and rodents.
04
Moisture and construction build-up
We design the construction build-up and moisture control individually, according to the type of space, the materials used and the building conditions. A cellar inside a house is treated differently from a basement in contact with soil.
Low-absorption insulants such as XPS or perimeter boards do not absorb moisture. On their own, however, they do not guarantee that water vapour will not condense within the structure – joints, penetrations and adjoining constructions are decisive. For more complex build-ups we recommend an assessment by a building designer or a building physics specialist.
Wine Master explicitly requires a separate vapour barrier for climate-controlled display cabinets (Wine ARM15 X manual, at the cabinet installation location). The manuals for cellar units do not prescribe one.
05
Floor, door and penetrations
- The floor must carry the racks and the wine. Whether and how to insulate it depends on the building and on what lies beneath. If it is insulated, the insulation must have sufficient compressive strength, with a load-spreading board on top (the Wine Master manual specifies a timber board of at least 15 mm).
- Insulate the door with the same material as the walls and seal it around the perimeter, or use an insulated door.
- Seal penetrations for pipes and cables; additionally insulate any central heating pipes running through the cellar.
- Glass is the weakest point in the insulation – see Glazed wine walls.
06
Sources
Technical data are based on the manufacturer’s current documentation: winemaster.fr and Wine Master manuals (IN25 X, version 07/2025, SP40 CA PRO, version 07/2025, SP40 DU PRO, version 14/2025). All manuals are available in the Documents section. The values are the manufacturer’s minimum requirements and do not replace a design for a specific building.
07 / Related
Continue
08 / Questions
Frequently asked questions
Is it enough to insulate just the walls?
It depends on the building and the adjacent spaces – we design the build-up individually. For Wine Master cooling units, however, the manufacturer’s cellar unit manuals give an insulation table for all surfaces, including the ceiling, floor and door, and make the warranty conditional on it. We assess in the design how to meet this condition for your particular cellar.
Can I use mineral wool?
Not in a climate-controlled wine cellar. Mineral wool can absorb moisture and lose its insulating capacity. EPS, XPS or PUR are suitable.
Does an underground cellar need insulation too?
The extent of insulation depends on the particular basement. Soil moderates temperature but does not guarantee it; we design which surfaces to insulate, and how, according to the building and the adjacent spaces – while taking into account the cooling unit manufacturer’s insulation requirements according to its table.
Enquiry
Send us a photograph of your space.
A short description, dimensions or a floor plan is enough for an initial assessment. We usually reply within one working day.